GEMMY Industrial in Bangladesh

Explore 62 unique GEMMY Industrial catalogue listings across Medical Equipment. Compare equipment and manufacturer references, then request a quotation for the model, accessories, delivery and support you need.

Plan your purchase: clinical laboratory and department equipment

Start with the application and the equipment already in use. These details help the team identify a suitable configuration and an itemised quotation.

Useful details for your quotation

Laboratory or clinical task and workload
Capacity, sample holders and exact model
Cleaning, utilities, accessories and acceptance requirements
Quantities, delivery location and required date
Installation, training, warranty and service requirements

Confirm the exact model, compatible accessories, documentation, current availability and delivery terms in writing. The catalogue describes equipment options; installation, acceptance and ongoing support are agreed for the proposed configuration.

Discuss GEMMY Industrial equipment

Request a quote

Products

OT-125A-128A operating table: OT-125A-128A is listed by GEMMY as an operating table, grouped on the manufacturer's site under its ENT treatment units heading. The specification and key features fields are both empty; the page carries the model number, the CE and ISO marks and a product photograph. Table movements, load rating and section configuration should be confirmed with GEMMY before the model is offered.
HD-7600S ENT treatment unit: HD-7600S is listed by GEMMY under its ENT treatment units heading, with the product name given only as treatment units. The manufacturer publishes no specification, no key features and no approval details for this model; the page carries the model number and a product photograph and nothing further. The configuration, the services built into the unit and the certification should all be confirmed with GEMMY before the model is offered.
SU-990 portable suction unit: A battery backed portable aspirator for emergency use, measuring 200 x 350 x 205 mm with an oil-less piston vacuum pump giving 13 to 15 litres per minute over a 0 to 600 mmHg range. A sealed lead acid 12 V rechargeable battery with automatic charging gives 1 to 1.5 hours from a full charge, with GEMMY offering an optional battery rated for 3 to 3.5 hours, and the charger works from the mains at the same time as the unit is in use. A plug-in cable allows operation from any 12 V DC supply, in an ambulance or a vehicle, which suits areas where mains failure, unstable current or blackouts are common. A three step switch selects suction, off and charge, and the 1000 ml collection bottle has overflow prevention.
SU-991 portable suction unit: The mains only version of GEMMY's 200 x 350 x 205 mm portable aspirator, with an oil-less piston vacuum pump that needs no lubrication or maintenance, giving 13 to 15 litres per minute across a 0 to 600 mmHg range. A 1000 ml collection jar graduated in millilitres, in autoclavable plastic or glass, carries a fluid overflow preventive stopper. A built-in vacuum gauge reads 0 to 760 mmHg, or 0 to 30 inHg, for direct reading. GEMMY states the models are CE certified to the electromagnetic compatibility requirements of EN60601-1-2.
SU-770 portable suction unit: A low profile portable aspirator measuring 320 x 145 x 240 mm, driven by an oil-less piston vacuum pump that requires no lubrication and no maintenance. Airflow is 13 to 15 litres per minute over a vacuum range of 0 to 600 mmHg, drawn into a single 1000 ml collection jar with an overflow preventive stopper, available in autoclavable plastic or glass. The built-in vacuum gauge reads 0 to 760 mmHg, or 0 to 30 inHg. GEMMY states the models are CE certified to the electromagnetic compatibility requirements of EN60601-1-2.
SU-305P mobile suction unit: A trolley mounted theatre aspirator measuring 500 x 420 x 885 mm, whose body is moulded in one piece from compact fibreglass for resistance to rust, chipping and corrosion. It takes either an oil rotary pump at 191 W giving 80 litres per minute and 700 mmHg, or a two cylinder oil-less pump at 270 W giving 70 litres per minute and 680 mmHg. Two plastic collection bottles with overflow preventive fittings and autoclavable rubber bungs are changed over by a left to right control knob, and a built-in gauge reads 0 to 760 mmHg. Four anti-static rubber castors, two of them lockable, carry the unit, and it is supplied with two bottles, a footswitch and a length of autoclavable silicone suction tubing.
SU-510-1 mobile suction unit: A mobile theatre aspirator measuring 455 x 300 x 710 mm, offered with either an oil rotary pump at 191 W giving 80 litres per minute and 710 mmHg, or a single cylinder oil-less pump at 200 W giving 28 to 33 litres per minute and 680 mmHg. Two 1000 ml polycarbonate collection jars with overflow prevention are switched by a left to right control knob, and a built-in gauge reads 0 to 760 mmHg. GEMMY lists it for suction biopsy, surgery, endometrial curettage and obstetric and gynaecological work, mounted on four anti-static rubber castors of which two lock. It is supplied with two bottles, a footswitch and autoclavable, reusable silicone suction tubing.
SU-305 mobile suction unit: The largest trolley aspirator in the range at 640 x 395 x 825 mm, carrying two 3000 ml collection jars in glass or plastic with overflow prevention, and a storage cabinet on the back for accessories and tools. It takes either an oil rotary pump at 191 W giving 80 litres per minute and 700 mmHg, or a two cylinder oil-less pump at 270 W giving 70 litres per minute and 680 mmHg. Vacuum is regulated from zero to maximum and read on a built-in gauge covering 0 to 760 mmHg, with a left to right knob switching which bottle draws. Four anti-static rubber castors with two locks carry the unit, and GEMMY notes low noise operation suited to wards and theatres.
SA-232 portable autoclave: A portable steam steriliser with a 230 mm diameter by 410 mm deep chamber in 304 stainless steel, giving roughly 16 litres in an overall footprint of 335 x 430 x 600 mm. Design temperature is 140 degrees C, with sterilising pressure of 1.4 kg/cm2 at approximately 122 degrees C, and the published cycle table quotes 122 degrees C at 1.12 kg/cm2 for unwrapped, wrapped and liquid loads. Several internal programmes are preset for selection, and GEMMY lists the machine for dental clinics, hospitals and laboratories handling wrapped, unwrapped, liquid and utensil loads. Safety devices are an overheat and low water cut-off switch, a safety valve and a release valve.
SA-232X bench top autoclave: A bench top steam steriliser with a 230 mm diameter by 390 mm deep chamber in 304 stainless steel, approximately 16 litres, in an overall cabinet of 501 x 406 x 537 mm. Design temperature is 140 degrees C and the published working range for unwrapped, wrapped and liquid loads is 115 to 134 degrees C at 0.9 to 2.1 kg/cm2. GEMMY states the autoclave is manufactured in conformity with directive 93/42/EEC. Safety fittings are a safety valve, an emergency exhaust valve, a release valve, a door safety holder and a pressure control switch.
SA-300MA bench top autoclave: A Class B table top steriliser with a 40 litre chamber measuring 300 mm diameter by 570 mm deep, running at 121 or 135 degrees C with an automatic fill water system and a vacuum assisted drying stage selectable at 0, 15, 30, 35 or 40 minutes. Programmes cover wrapped and unwrapped loads, dry and undried, liquids, a PRION programme, Bowie-Dick and a pump test, with temperature shown digitally, pressure on a pressure and vacuum gauge and programme status on LED. It draws 3000 W at 14 A, split between a 2300 W heater, a 600 W dry heater and a 100 W vacuum pump, from a 230 V 50/60 Hz supply. Safety cover includes a 2.5 kg/cm2 pressure safety valve, independent over temperature protection, two 30 A no fuse breakers, an over pressure switch, a door lock micro-switch, water level sensors in both the tank and the chamber, and a silicone bellows pressure door lock.
HL-350 vertical steam autoclave: A vertical steam steriliser whose cycle runs automatically through conditioning and sterilising phases, with sterilising temperature adjustable from 121 to 132 degrees C and sterilising time from 0 to 60 minutes. The timer only starts once the preset temperature has been reached, and a buzzer announces completion and cuts the heating supply. The cylindrical chamber is SUS 316 stainless steel with a polished surface, thermally insulated with fibreglass and clad in stainless sheet, fitted with a steam trap to discharge condensate and a HEPA air filter to keep contaminated air out. The door is operated manually by a rotating handle with a foot pedal to lift it, sealed by a silicone rubber gasket, and safety cover includes a door interlock, a safety valve, over temperature cut-off, circuit breaker and fuse protection, and a manual emergency exhaust for power outages.
HL-341 vertical steam autoclave: A 72 litre vertical steam steriliser with a 350 x 750 mm chamber, working from 120 to 134 degrees C under pressure control, with a gross weight of 140 kg. A semi-automatic control system uses a sterilising and drying switch to select which function runs, and both sterilising and drying times are adjustable from 0 to 60 minutes on the timer. The timer starts only after the preset temperature is reached, illuminated pilot lamps show status, and a buzzer announces completion and cuts the heating supply. An automatic air venting device discharges cool air from the chamber to obtain effective saturated steam, and the machine comes with a sterilisation basket, two tube indicators, a shelf and a hose.
TC-612 high pressure horizontal steam steriliser: GEMMY horizontal steam steriliser listed here under the TC-612 catalogue name. The manufacturer's current TC-A series documentation identifies TC-612A; its ratings must not be assumed to apply to every unit labelled TC-612. Send the full model suffix or equipment nameplate, intended loads and available electrical supply so chamber, cycle and utility requirements can be confirmed for your enquiry.
PLC-025 universal centrifuge: A benchtop universal centrifuge with a stainless steel chamber, adjustable up to 5000 rpm with digital display and a maximum RCF of 4124 x g. Gemmy lists automatic imbalance detection, an electric lid interlock, a 99 minute digital timer and a maximum capacity of 240 ml.
PLC-012 universal centrifuge: A benchtop universal centrifuge with a moulded stainless steel chamber, analogue speed control and a mechanical timer, running from 0 to 12000 rpm depending on the rotor fitted. Rotors are interchangeable using the supplied hexagon wrench, and a safety locking latch cuts the motor if the lid is opened during a spin.
KHT-410 micro haematocrit centrifuge: A micro haematocrit centrifuge that takes 24 capillary tubes on an F-2415 rotor, reaching approximately 12000 rpm and a maximum RCF of 14490 x g. It has a 30 minute timer, a toggle switch brake and a safety lid lock.
DBC-8E differential blood cell counter: An electronic differential blood cell counter with eight keys covering the Schilling groups of leucocytes, an LED display reading 0 to 999 and a totaliser. A buzzer sounds at every 100 cells counted, and the percentage for each cell type can be read from the display.
YCW-01 water bath: A 22 litre thermostatic water bath working from 5 degrees C above ambient up to 100 degrees C, with analogue temperature setting and a thermometer readout. The moulded bath has rounded corners and stainless steel sides with no seams, and a rotating stirrer directs flow around the tank to even out temperature.
SU-510 portable suction unit: An AC-powered portable suction unit measuring 450 x 250 x 310 mm, offered with either an oil rotary vane or an oil-less piston vacuum pump. It comes with two 1000 ml graduated collection jars with overflow prevention stoppers, a built-in vacuum gauge reading 0 to 760 mmHg, and a footswitch. Portable describes its form factor; GEMMY does not list battery operation for SU-510.
IN-010 laboratory incubator: A forced convection laboratory incubator for tissue culture and microbiological work, with microprocessor PID control and a temperature range from ambient plus 5 degrees C to 75 degrees C. Gemmy lists capacities from 16 to 200 litres, a digital 99 hour timer, an over temperature alarm and cut-out, and a tempered glass viewing window in the front door.
VRN-360 orbital shaker: GEMMY lists the VRN-360 orbital shaker for laboratory mixing. Request a current datasheet identifying the exact model code, working range, dimensions and included accessories before confirming a purchase. Supply your application, sample/load information and intended operating schedule so the proposed configuration can be checked.
PLC-01 centrifuge: GEMMY's entry level benchtop centrifuge, built around a fixed angle A-0415 rotor that takes four 15 ml or 10 ml test tubes and collects sediment diagonally for higher effective speed and RCF. Speed is regulated from 1000 rpm up to the maximum within 15 seconds, with a mechanical 60 minute timer and an LED lamp confirming the power is on. A heavy cast iron base and three rubber suction feet stop the unit creeping, and anti-vibration rubber buffers balance the rotor while it spins. GEMMY states the unit meets the CE electromagnetic compatibility requirements of EN60601-1-2 and the IEC801 series.
PLC-02 table top centrifuge, 6 tubes: A six place table top centrifuge holding tubes of 10 or 15 ml on a fixed angle rotor, with a speed range of 1000 to 4000 rpm and a 4500 rpm variant available. Setting is by mechanical 60 minute timer, and an LED lamp indicates that power is applied. GEMMY offers a fixed speed build on request and an automatic shutout safety device as an option, and the cast iron base with three rubber suction feet keeps the unit stable through a run. The listing quotes ISO 9001, ISO 13485, CE, GMP and FDA against the model.
PLC-03 table top centrifuge: An eight place table top centrifuge fitted with the A-0815 rotor for 15 ml or 10 ml test tubes, running to a maximum of 4500 rpm. Control is by mechanical 60 minute timer with an LED lamp as the power indicator. The cabinet measures 270 x 270 x 250 mm, the same footprint as the rest of the PLC bench range. GEMMY lists CE, ISO, GMP and FDA against the model.
PLC-012E universal centrifuge: The digital member of the PLC-012 pair, specified with an LED digital tachometer, a 99 minute digital timer and microprocessor speed control, where the base PLC-012 uses an analogue tachometer and a mechanical timer. GEMMY quotes 0 to 12000 rpm across the PLC-012 series depending on which rotor is fitted, driven by an 80 W brush motor inside a moulded stainless steel chamber. Rotors are changed quickly using the attached hexagon wrench, and a safety locking latch with an interlock switch cuts the motor if the lid is opened mid spin. The cabinet measures 310 x 360 x 310 mm and the drive brakes to a gentle stop in 20 seconds.
PLC-036 universal centrifuge: A brushless universal centrifuge adjustable from 1000 to 12000 rpm on a three digit LED readout, with microprocessor speed control and a two digit 99 minute timer. Universal multi-voltage operation from 100 V to 240 V removes the need for a transformer, and the stainless steel chamber carries automatic imbalance detection, an overheating sensor on motor and driver, an interlocking lid with manual override for power failures and an emergency stop. Five rotors are published for the machine, from an eight place 15 ml angle rotor to the F-2415 capillary rotor for haematocrit work at a fixed 12000 rpm and 14490 x g. A transparent viewfinder in the lid allows the rotor to be watched while it spins.
PLC-036H universal centrifuge: A brushless universal centrifuge adjustable from 1000 to 5000 rpm, running on a universal 100 V to 240 V, 50/60 Hz supply with microprocessor speed control and a two digit 99 minute LED timer. The stainless steel chamber is protected by imbalance detection with alarm and brake, an overheat alarm, a safety interlocking lid with an override for power failure, an emergency stop and a shutout device that acts when the lid is opened. GEMMY publishes eight rotors for the machine, ranging from the A-2420 at 15000 rpm and 20630 x g down to the H-0450 for four 50 ml tubes, including the F-2415 capillary rotor for haematocrit testing at 12000 rpm and 14490 x g. The cabinet measures approximately 320 x 400 x 310 mm and weighs 17 kg without a rotor.
PLC-012H universal centrifuge: A universal benchtop centrifuge with microprocessor speed control, a digital 99 minute timer and a stainless steel chamber, driven by a 120 W brush motor. Safety cover comes from a lid lock, an electrical switch brake and a safety shutout. GEMMY lists the S-0815 special small eight place swing-out rotor for 15 ml tubes against this model. Approvals quoted are ISO 9001, ISO 13485, GMP, CE and FSC.
DBC-06 differential blood cell counter: A manual laboratory counter for differential blood cell counts, offered as a five unit or eight unit lab-count with a totaliser. The keys correspond to the normal Schilling groups of leucocytes, basophil, eosinophil, segmented, lymphocyte, monocyte, myelocyte, juvenile and stab, each key carrying the name and picture of the cell it records. Every stroke registers both on the unit belonging to the key pressed and in the window above it, and a bell rings once a total of 100 cells has been counted. Rotating the handle anti-clockwise clears the figures.
DBC-9 manual differential blood counter: An eight unit manual differential blood counter with a totaliser, for simplifying differential blood cell counts at the haematology bench. The eight keys represent the normal Schilling groups of leucocytes and each carries the name and picture of the cell it records. Each stroke registers both in the unit corresponding to the key pressed and in the window, and a bell rings at every 100 cells counted. Figures are cleared by rotating the handle anti-clockwise.
YCW-012S shaking water bath: A reciprocating shaking water bath built on a microprocessor digital controller that displays the actual bath temperature and holds uniformity to +/-0.1 degrees C. Shaking stroke is set on a control knob from 20 to 200 rpm, produced by an induction motor giving a 20 mm circular motion at 0 dB. Tube racks and the flask platform can be raised, lowered and removed to suit different vessel lengths, or taken off entirely when shaking is not wanted. An audible over temperature alarm cuts the power at 2 degrees C above the set point, and temperature recalibration is available when the actual reading drifts from the display.
YCW-010 water bath: A digitally set thermostatic water bath offered in 22 litre and 11 litre tanks, working from 5 degrees C above ambient to 100 degrees C with PID control and a maximum setting of 99.9 degrees C. Stability and uniformity are both quoted at +/-0.01 degrees C, held by a rotating stirrer that directs flow around the tank. The moulded bath has rounded corners and seamless stainless steel sides, and the immersion heating element is sheathed in stainless steel and rated at 1.0 kW. Audible and visible alarms cut the power at 2 degrees C above the set point. Concentric ring covers, a drain valve and a perforated tray are offered as options.
YCW-010E water bath: The timed version of GEMMY's digital thermostatic bath, in 22 litre and 11 litre tanks, with digital setting, LED digital readout and PID control to a maximum of 99.9 degrees C. Stability and uniformity are both listed at +/-0.01 degrees C and the sheathed immersion heater is rated at 1.0 kW. The timer only begins once the set temperature has stabilised, and the display shows END when the cycle finishes. Audible and visible alarms shut out power at 2 degrees C above the set point, and a drain valve and perforated tray are available as extras.
YCW-03S water bath: A 22 litre thermostatic bath set by thumb switch with three preset points at 25, 37 and 56 degrees C, the temperatures a serology and haematology bench uses most. Readout is LED digital, control is PID, and stability is quoted at +/-0.05 degrees C with uniformity at +/-0.01 degrees C to a maximum of 100 degrees C. A temperature recalibration function corrects drift between the actual and displayed value. GEMMY offers stainless steel gable lids, concentric ring covers with openings of 107, 80, 55, 31.5 and 21 mm, and mesh tube racks for 13 mm or 18 mm tubes in 40 or 20 wells.
YCW-05 water bath: The small bath in GEMMY's constant temperature range, a 5 litre analogue unit with a thermometer readout and a stainless steel sheathed immersion heating element. It works from 5 degrees C above ambient up to 100 degrees C for biological, clinical research, medical, biochemical, industrial and teaching laboratories. The moulded tank has rounded corners and seamless stainless steel sides for even circulation and easy cleaning, and a rotating stirrer directs flow around the tank to improve uniformity. Concentric ring covers are offered to cut heat loss when flasks are suspended in the bath.
KHT-410E haematocrit centrifuge: A micro haematocrit centrifuge for packed cell volume work, used in biochemistry, microbial immunity genetics, blood separation and general clinical testing to establish the percentage of red blood cells against whole blood, which can indicate anaemia or polycythaemia. GEMMY states that all models in the range run at a fixed 12000 rpm apart from the PLC-012 and PLC-012E. The time is set and the run started with the START button, the rotor lid must be closed before spinning, and a reading scale is supplied so the capillary tube can be read directly. EPDM is used for the rotor gasket to extend service life, and a safety device cuts the power if the lid is opened during operation.
KHT-400: KHT-400 is listed by GEMMY within its micro haematocrit centrifuge range, alongside the KHT-410 and KHT-410E. The manufacturer publishes no product name, no specification, no key features and no approval details for this model; the page carries only the model number and a product photograph. Specification, capillary tube capacity and speed should be confirmed with GEMMY before the model is offered.
PB-3320: A binocular laboratory microscope with a measuring single tube inclined at 45 degrees and rotating through 360 degrees, with interpupillary distance adjustable from 48 mm to 75 mm. It is supplied with WF10X and WF16X eyepieces and a four position achromatic objective set of 4X, 10X, 40X and 100X. The double layer mechanical stage measures 140 x 130 mm with a 70 x 50 mm moving range, over an N.A. 1.25 Abbe condenser with iris diaphragm. Coaxial coarse and fine focusing runs on a rack and pinion mechanism with a fine focusing scale value of 0.002 mm, lit by a built-in 6V 20W variable brightness lamp. GEMMY publishes no product name for this model, only the model number PB-3320.
PB-3620 binocular microscope: A binocular microscope whose measuring single tube is inclined at 30 degrees rather than the 45 degrees of the rest of the PB range, rotating through 360 degrees with interpupillary distance from 48 mm to 75 mm. WF10X and WF16X eyepieces pair with achromatic objectives of 4X, 10X, 40X and 100X. The double layer mechanical stage measures 135 x 125 mm with a 70 x 50 mm moving range, over an N.A. 1.25 Abbe condenser with iris diaphragm. Focusing is coaxial coarse and fine on a rack and pinion mechanism with a fine focusing scale value of 0.002 mm, and illumination is a built-in 6V 20W variable brightness source.
PB-3730 trinocular microscope: The trinocular member of the PB range, with a triple measuring single tube at 45 degrees rotating through 360 degrees and interpupillary distance from 48 mm to 75 mm. It carries WF10X and WF16X eyepieces with achromatic objectives at 4X, 10X, 40X and 100X, and a 140 x 130 mm double layer mechanical stage with a 70 x 50 mm moving range. The third port is intended for a CCD digital camera, which GEMMY lists as an optional accessory together with plan objectives and a connection adaptor. Focusing is coaxial coarse and fine with a 0.002 mm fine scale value, under 6V 20W variable brightness illumination.
PB-3428 binocular microscope: A binocular microscope specified with infinity plan achromatic objectives at PL 4X/0.10, PL 10X/0.25, PL 40X/0.65 and PL 100X/1.25, all long working distance, paired with WF 10X eyepieces giving a 20 mm field. The double layer mechanical stage is the largest in the PB range at 180 x 150 mm, with a 75 x 50 mm moving range. Focusing is coaxial coarse and fine on a rack and pinion mechanism with a fine focusing scale value of 0.002 mm, and the condenser is an N.A. 1.25 Abbe type with iris diaphragm.
PF-373 trinocular fluorescence microscope: A trinocular fluorescence microscope with the head inclined at 45 degrees and interpupillary distance from 55 mm to 75 mm, fitted with WF10X eyepieces giving an 18 mm field. The objective set is fluorescent throughout at 4X/N.A. 0.10, 10X/N.A. 0.25, 40X/N.A. 0.65 spring loaded and 100X/N.A. 1.25 spring loaded oil. Epi-illumination is by a 220V or 110V 100W mercury lamp with a B and G wave band fluoroscope box, while transmitted light uses a 6V 20W halogen bulb. The double layer mechanical stage measures 140 x 130 mm with a 75 x 50 mm moving range, over an N.A. 1.25 Abbe condenser with iris diaphragm and blue filter.
PD-2520 binocular microscope with measuring and capture software: A digital binocular microscope combining a measuring tube at 45 degrees with 360 degree rotation, a 1.3 megapixel CMOS camera system and capture software. Magnifications of 40X, 100X, 400X and 1000X come from achromatic objectives of 4X, 10X, 40X spring loaded and 100X spring loaded oil, with WF10X eyepieces giving a 20 mm field and interpupillary distance from 55 to 75 mm. The supplied software takes photographs, records video and measures actual length, area, diameter, circumference and angle. The double layer mechanical stage is 130 x 120 mm with a 70 x 30 mm moving range, over an N.A. 1.25 Abbe condenser with iris diaphragm and filter.
PS-824F stereo microscope: A zoom stereo microscope with a binocular measuring single tube at 45 degrees and 360 degree rotation, interpupillary distance from 55 to 75 mm and diopter adjustment of +/-5 degrees. GEMMY publishes zoom body magnification of 1X to 3X and 2X to 40X, giving total magnifications of 10X to 30X and 20X to 40X, at a 90 mm working distance over a 75 mm glass stage. Both vertical and transmitted illuminators are 6V 15W with variable brightness. A dust cover and two eye shields are supplied, with 20X eyepieces offered as an option.
P-1 portable microscope: A handheld USB microscope measuring 95 mm long by 32 mm in diameter, focusing manually from 10 mm to infinity and running at 30 frames per second over a USB 2.0 interface. Eight white light LEDs at the tip give four adjustable illumination levels, and buttons on the top of the barrel capture stills and change brightness without touching the computer. The measurement function reads actual length, area, diameter, circumference and angle in millimetres, inches or mils, and the unit doubles as a USB camera. GEMMY lists resolutions of 1280 x 1024 and 640 x 480, BMP and AVI output, and English and Traditional Chinese software versions.
Vegetable capsule: A vegetable capsule consumable retained from the GEMMY catalogue for buyers seeking empty capsule shells. This listing covers the capsule shell; filling equipment is separate. Confirm current supply, shell material, size and the intended filling process before ordering. Request the offered product specification and relevant batch documentation, and check compatibility with the formulation and filling equipment rather than assuming that a catalogue size guarantees fit.
VM-300 vortex mixer: A benchtop vortex mixer running to 3150 rpm with a single tube head, or 1800 rpm with the 3 inch pad, driven by a 5.6 mm eccentric. Two mixing heads are interchangeable: a 26 mm diameter rubber cup for conventional single tube work, and a 3 inch platform pad for multiple tubes or a flask. Operation is either TOUCH for intermittent running, where stirring intensity is controlled by the pressure applied to the pad, or SWITCH for continuous mixing at the flip of a switch. The unit measures 130 x 165 x 180 mm and weighs 5.0 kg, heavy enough to resist slipping and creeping under vibration.
VM-300P vortex mixer: A vortex mixer measuring 145 x 170 x 185 mm with a 4.2 mm eccentric, reaching 3200 rpm on a single tube and 1500 rpm with the 3 inch pad fitted. Like the rest of the VM range it offers both touch and switch modes, touch for short intermittent bursts and switch for continuous running. GEMMY lists CE, ISO and GMP against the model.
VM-370 3D roller mixer: A seven roller mixer that rocks and rolls simultaneously at a fixed 40 rpm, plus or minus 3 rpm, for blood samples, reagents and viscous substances that need a gentle action rather than a vortex. A 19 mm diameter eccentric produces three dimensional rocking at both sides, motioned by built-in POM gears and a 24 V 5.17 W gear motor. Rollers are 32 mm in diameter and 320 mm long, alkali and acid resistant, taking 18 tubes of 5 ml, 12 of 10 ml, 12 of 15 ml or 12 of 50 ml up to a 5 kg load. A mechanical 180 minute timer allows continuous or intermittent operation, and GEMMY specifies operation from 4 to 60 degrees C, 40 to 90 per cent humidity, up to 4000 metres altitude and 700 to 1060 hPa.
VRN-200 orbital shaker: GEMMY lists the VRN-200 orbital shaker for laboratory mixing. Request a current datasheet identifying the exact model code, working range, dimensions and included accessories before confirming a purchase. Supply your application, sample/load information and intended operating schedule so the proposed configuration can be checked.
VRN-210 orbital shaker, rotor: GEMMY lists the VRN-210 orbital shaker, rotor for laboratory mixing. Request a current datasheet identifying the exact model code, working range, dimensions and included accessories before confirming a purchase. Supply your application, sample/load information and intended operating schedule so the proposed configuration can be checked.
VRN-480 orbital shaker, rotator: The heavy duty shaker in the range, with a 422 x 282 mm platform, a triple eccentric drive and counterbalance that hold a vibration free 25.4 mm orbit at speed even under heavy or unbalanced loads. Solid state control covers 40 to 400 rpm and the platform carries 15 kg at 100 rpm, with speed shown on an analogue tachometer or a three digit LED so runs can be repeated accurately. The platform turns on six permanently lubricated sealed ball bearings, and the precision machined drive housing sits on four cushioned feet that stop the unit creeping. Flask platforms are listed as GE-125-15 for fifteen 125 ml flasks, GE-250-11 for eleven 250 ml flasks and GE-500-06 for six 500 ml flasks, and timed operation runs up to 180 minutes.
VRN-380 rocking shaker: A rocking shaker measuring 305 x 325 x 190 mm, offered in two builds. The VRN-380A is digital, with a 99 minute timer plus hold, a tachometer and a brushless motor. The VRN-380B is mechanical, with a 180 minute timer plus hold, a dial meter and a carbon brush motor. GEMMY lists ISO, CE and GMP against the model.
PS-2A pipette shaker: A six place pipette shaker measuring 140 x 170 x 155 mm, fitted with a timer. GEMMY lists CE, ISO and GMP against the model.
PS-8B pipette shaker: An eight place pipette shaker measuring 175 x 160 x 115 mm. GEMMY lists no timer on this model and quotes CE, ISO and GMP against it.
YCO-010 hot air oven: A forced convection hot air oven and dry heat steriliser offered in eight capacities from 16 to 200 litres, working from ambient plus 5 degrees C to 250 degrees C under microprocessor PID control. GEMMY quotes temperature uniformity of +/-3.0 degrees C and stability of +/-0.5 degrees C, both measured at 180 degrees C, with the timer only starting once the actual temperature reaches 2 degrees C below the set point. Double wall construction with heavy gauge glass fibre insulation retains heat, and adjustable fresh air inlet ports at top and bottom control the amount of convective air. Safety cover includes an over temperature alarm and cut-out at 10 degrees C above the set point and an independent safety switch that removes power at 220 degrees C if the primary control fails.
YCO-N01 analogue hot air oven: GEMMY lists the YCO-N01 analogue hot air oven for dry-heat laboratory processing. Request a current datasheet identifying the exact model code, working range, dimensions and included accessories before confirming a purchase. Supply your application, sample/load information and intended operating schedule so the proposed configuration can be checked.
DB-005 dry bath incubator, block heater: The compact analogue dry bath in GEMMY's range, weighing 2.5 kg with a 200 W heater and a maximum of 105 degrees C, holding uniformity at 37 degrees C to 0.3 degrees C under PID control. Temperature is set on an analogue control and read from a thermometer, with an over heat alarm fitted. Applications listed include incubating DNA specimens, cross matching and screening in the blood bank, incubating melted agar, enzyme assays, digestions and milk residue tests, as well as serology, haematology, pathology and biochemistry work. Interchangeable heating blocks accept test tubes, cuvettes and microcentrifuge tubes, each with a well for a removable thermometer, and a solid block with no holes turns the unit into a hot plate.
DB-006 dry bath incubator, block heater: The larger analogue dry bath, 3.5 kg with a 450 W heater reaching 105 degrees C, with uniformity at 37 degrees C quoted at 0.5 degrees C under PID control. Setting is analogue with a thermometer readout and an over heat alarm. It covers the same bench work as the rest of the DB range: incubating DNA specimens, blood bank cross matching and screening, melted agar, enzyme assays, digestions, milk residue tests, serology, haematology, pathology and biochemistry. Heating blocks are interchangeable for test tubes, cuvettes and microcentrifuge tubes, each with a thermometer well, and a solid block converts the unit to a hot plate.
DB-006E dry bath incubator, block heater: The digital dry bath in the range, with digital setting, an LED digital readout and a digital 99 hour timer, which the analogue DB-005 and DB-006 do not carry. The 450 W heater runs to 99 degrees C with uniformity at 37 degrees C quoted at 0.5 degrees C under PID control, and an over heat alarm is fitted. Net weight is 5.5 kg. The same interchangeable heating blocks accept test tubes, cuvettes and microcentrifuge tubes, each with a well for a removable thermometer, and a solid block turns the unit into a hot plate.
IN-601 laboratory incubator: A laboratory incubator offered in six capacities from 34 to 150 litres, working from ambient plus 5 degrees C to 75 degrees C, in either an analogue or a digital build. The analogue version uses ON/OFF control with a mercury thermometer on the top of the cabinet and natural gravity convection, giving uniformity of +/-5.0 degrees C and stability of +/-3.0 degrees C at 37 degrees C. The digital version uses microprocessor PID control with forced convection, tightening uniformity to +/-3.0 degrees C and stability to +/-1.0 degrees C at 37 degrees C, and cuts out at 4 degrees C above the set point rather than at 80 degrees C. On the digital model the mechanical 180 minute timer starts only once the set temperature has stabilised, shows END when the cycle finishes, and stores the temperature and elapsed time if the door is opened mid run.

GEMMY Industrial equipment: purchase questions

Which GEMMY Industrial equipment can I find here?

This VVON catalogue covers clinical laboratory and department equipment. Use the category filter or search a product or model, then open the product page for its description and manufacturer reference. Catalogue entries do not establish current local stock or every product in the manufacturer's worldwide range.

What details help prepare a GEMMY Industrial quotation?

Include: Laboratory or clinical task and workload; Capacity, sample holders and exact model; Cleaning, utilities, accessories and acceptance requirements. Add the quantities, delivery location and required date. You can add several products to one enquiry list or request help selecting the configuration.

What affects GEMMY Industrial equipment pricing in Bangladesh?

Specify load or sample type, capacity, cycle or speed requirements, baskets or rotors and utilities. Keep optional accessories, documentation, installation and maintenance scope visible in each offer. Request a dated, itemised quotation stating currency, taxes, delivery, warranty and service responsibilities. A catalogue listing is not a current price or local-stock commitment.