Honeywell in Bangladesh

Vvon Technologies Limited supplies, installs and services Honeywell equipment across Bangladesh. 164 products are catalogued across Scientific & Laboratory Equipment, Nanotechnology.

Categories

• Gas Detection & Safety (148)
• Cleanroom Gas Safety & Generation (8)
• Electron Microscopy & Microanalysis (4)
• Metrology & Position Measurement (3)
• Laboratory Instruments (1)

Products

• AutoRAE 2 Automatic Test and Calibration System: Modular bump test and calibration station for RAE Systems gas monitors. It runs as a single bench unit or networked to support up to ten cradles at once and calibrate for up to five distinct gases, with one touch bump testing.
• MicroDock II Dock Calibration System 3 inlet: Portable automated test and calibration station for Honeywell portable gas detectors, in a three gas inlet configuration. It needs no computer, expands by adding modules and runs bump tests and calibrations on several instruments at once.
• MicroDock II Dock Calibration System 4 inlet: Portable automated test and calibration station for Honeywell portable gas detectors, in a four gas inlet configuration. Fully portable and expandable, it manages bump testing and calibration without a connected computer.
• FS24X Flame Detector: Multi-spectrum triple infrared flame detector from the FSX family, combining WideBand IR, 4.3 micron IR and visible sensing. Dual microprocessors run the discrimination algorithms so that real fires are called quickly while false alarm sources are rejected.
• FS20X Plus: Combined ultraviolet and triple infrared flame detector for hydrocarbon, non hydrocarbon and hydrogen fires. It keeps working through rain, fog and smoke, carries marine certifications and is SIL2 rated for safety instrumented system duty.
• FS10 Flame Detector: Microprocessor based fire detection and process control system built for liquid and powder coating lines. It senses flame and shuts down the electrostatic finishing process within milliseconds, before wet paint film and residue can ignite.
• FS20X Flame Detector: Multi-spectrum UV, dual IR and visible flame detector with a solar blind ultraviolet sensor. It responds faster and over a longer range than conventional narrow band UV and IR units, across a wide operating temperature band.
• FS24X Plus Flame Detector: Triple infrared flame detector using WideBand IR technology to pick up hydrocarbon and hydrogen fires early, even through rain, fog and smoke. Built for hazardous locations, with marine certifications, window clarity diagnostics and SIL2 rating.
• 301C Controller: Three channel controller for toxic gas, combustible gas and oxygen hazards. Addressable RS-485 Modbus daisy chain wiring connects up to 96 transmitters over two pairs of wires, and zoning and averaging functions cut installation and maintenance cost.
• FSL100 Flame Detectors: Optical flame detector range for light industrial and commercial fire hazards, offered in UV, IR and UV/IR variants. Wide area coverage and fast response are combined with built in automatic self test, and test lamps are available for every model.
• EchoView Host Mini-Controller: Portable wireless mini controller that acts as the hub for a mobile network of RAE Systems gas monitors. It receives readings, call names and alarm status from up to eight instruments and displays them live, with range extendable past one kilometre using mesh routers.
• Manning GM-JR: Standalone readout and alarm unit for industrial refrigeration gas monitoring. It offers an adjustable setpoint, relay output and 4 to 20 mA signal, and suits OEMs and plants that already run their own control system but need remote indication.
• Touchpoint™ Plus Controller: Wall mounted gas detection control system supporting up to sixteen channels. Its modular build and menu driven interface let operators configure inputs, alarm levels and relay actions for a wide range of fixed detection applications.
• Touchpoint™ Plus Wireless Controller: Hybrid multi-channel controller with a built in wireless modem that combines hard wired sensors with a MeshGuard wireless network. It gathers data and drives alarms from MeshGuard toxic gas, flammable gas and flame monitors on one screen.
• Touchpoint Pro Controller: Modular gas detection control system built on a building block approach, so the same platform scales from a few points to a large site. Configuration, installation and day to day operation are handled through a touchscreen interface.
• Unipoint Controller: DIN rail mounted single channel controller that brings flammable, toxic or oxygen gas detection into an existing control system. It fits inside a plastic or metal enclosure for indoor, outdoor or potentially explosive locations, in mV bridge or mA versions.
• 301IRF Refrigerant Gas Detector: Infrared refrigerant gas sensor for chiller rooms, mounted low on the wall or on the chiller pad to catch leaks at source. Housed in rugged ABS polycarbonate and used with a 301EM-20 controller for ASHRAE 15 and B-52 compliance.
• 705 High Temperature Flammable Gas Sensor: Combustible gas sensor for high temperature hazardous areas such as turbine enclosures and solvent drying ovens. A matched pair of poison resistant catalytic elements holds the baseline stable, so low level alarm settings stay reliable across a wide temperature range.
• FS7 Fire and Flame Detector: Flame detector for semiconductor wet bench fires with a two stage response. It raises an alert at a 3 kW fire so a small fire can self extinguish, then alarms at the Factory Mutual threshold of 13 kW if the fire keeps growing.
• Manning AirScan IR-F9 Gas Detector: Infrared diffusion sensor for refrigerant gases, selective to fluorocarbons and free from vibration effects. SensorCheck technology continuously monitors sensor performance, and the stabilised design keeps accuracy over long service life.
• Manning EC-FX-NH3 Gas Detector: Electrochemical ammonia sensor for cold storage, refrigerated process areas and engine rooms. It holds sensitivity and accuracy through rapid swings in temperature and humidity, so one sensor type covers all three environments.
• E3Point Gas Detector: Networkable toxic and combustible gas monitor for commercial buildings, car parks and outbuildings. It covers CO, NO2, O2, H2, H2S, CH4 and C3H8, and runs standalone with single or dual gas detection or as a BACnet or Modbus node.
• Manning Vent Line Gas Detector: Sensor that watches refrigeration vent line headers for high concentrations of ammonia or fluorocarbons. A reading in the vent line warns of system overpressure or a leaking relief valve before refrigerant loss and downtime build up.
• OELD (Optima Excel Local Display): Smart junction box for Searchpoint Optima Plus and Searchline Excel detectors. It bridges the 4 to 20 mA signal to the controller and adds an LCD gas reading, a traffic light status indicator and Bluetooth Low Energy pairing in a metal housing.
• OmniPoint™ Gas Detector: Hazardous area gas transmitter that supports up to three sensors on one head for toxic, oxygen and flammable hazards. Multiple sensor technologies, a full colour touch key interface and Bluetooth operation make setup and maintenance straightforward.
• RAEGuard 2 PID Gas Detector: Fixed photoionisation detector that measures a broad range of volatile organic compounds. It runs on 10 to 28 VDC with a three wire 4 to 20 mA output and RS-485 Modbus, and the digital PID module can be removed in hazardous locations for service.
• RAEGuard 3 Gas Detector: Fixed transmitter covering combustible, toxic and oxygen hazards using catalytic bead, compensated electrochemical and NDIR infrared sensing. The combustible sensor uses long life anti poisoning technology, and oxygen cells need no nitrogen zero calibration.
• RAEGuard Lite Gas Detector: Modular fixed detector for continuous monitoring of flammable, toxic and oxygen hazards indoors or outdoors. It provides a standard three wire 4 to 20 mA analogue output alongside Modbus RTU, and the design keeps installation and maintenance cost down.
• Searchline Excel™ Cross-Duct Open Path Gas Detector: Open path infrared gas detector configured for HVAC intakes, exhaust ducting and turbine enclosures, and certified for hazardous areas. It gives fast response over a short path and is often paired with Searchpoint Optima Plus point detection.
• Searchline Excel™ Edge Open Path Gas Detector: Long range open path detector for flammable hydrocarbons, aimed at perimeter and fence line monitoring. Mounted at the site boundary it keeps detecting reliably through harsh and changing weather conditions.
• Searchline Excel Open Path Infrared Gas Detector: Infrared open path flammable gas detector with more than 6,000 units installed worldwide, from Arctic sites to desert plant. It is immune to interference from other infrared sources and holds calibration over long unattended periods.
• Searchline Excel™ Plus Open Path Gas Detector: Short to medium range open path detector for flammable hydrocarbons in upstream and downstream oil and gas plant. Its optical design keeps measuring through thick fog and other visibility loss that stops many infrared and laser detectors.
• Searchpoint Optima Plus Point Infrared Gas Detector: Infrared point detector for hydrocarbon gases, certified for use in potentially explosive atmospheres. It draws on a worldwide installed base of over 100,000 units across duties from light industrial plant to offshore platforms.
• Searchzone Sonik™ Ultrasonic Gas Leak Detector: Acoustic leak detector that hears the ultrasonic sound of a high pressure gas escape rather than measuring concentration, so wind and weather do not affect it. It is factory calibrated, sealed, has no moving parts and mounts in any orientation.
• Sensepoint Flammable and Toxic Gas Sensor: ATEX certified sensor range covering flammable, toxic and oxygen hazards for general industrial monitoring. Installation in potentially explosive atmospheres uses a suitable Exd or Exe junction box, with industry standard outputs to a controller or DCS.
• Sensepoint Gas Sensor: Fixed sensor head for flammable and toxic gas monitoring, wired back to a Honeywell controller. It uses an mV bridge output for the flammable version and is rated IP65, so it can be mounted in general industrial plant areas.
• Sensepoint Gas Sensor with Junction Box: Sensepoint flammable, toxic or oxygen detector supplied pre-wired in a junction box, ready to install with conduit or armoured cable. It suits indoor and outdoor duty and ATEX approved potentially explosive atmospheres.
• Sensepoint XCD Gas Detector: Fixed transmitter for combustible, toxic and oxygen hazards in potentially explosive atmospheres, indoors or outdoors. Toxic and oxygen sensors can be mounted remotely from the transmitter, which helps in hard to reach or high temperature locations.
• Sensepoint XCD RFD Gas Detector: Remote flammable detector version of Sensepoint XCD, designed for use with a remotely mounted combustible gas sensor in Class 1 Division 1 areas. It suits duties where the sensing point sits well above ambient temperature.
• Sensepoint XCL Gas Detector: Fixed gas detector for light industrial and commercial spaces with Bluetooth Low Energy built in. Pairing the unit with a smartphone lets an engineer adjust set points and read fault codes from up to ten metres away.
• XNX™ Universal Transmitter: Universal gas detection transmitter that accepts the widest range of Honeywell sensor technologies on one platform, with a modular choice of inputs and outputs. It works alongside Searchline Excel, Searchpoint Optima, third party PLCs and digital bus systems.
• Sensepoint XRL Gas Detector: Fixed point gas detector with Bluetooth, configured from a smartphone or tablet running the Sensepoint app. It is available as a flammable detector for potentially explosive gases or as a toxic detector for common industrial gas hazards.
• Sensepoint XCD RTD Gas Detector: Remote toxic detector version of Sensepoint XCD for Class 1 Division 2 areas. The sensor can be mounted up to 100 feet from the transmitter, which keeps the detection point where it is needed while the display stays accessible.
• Honeywell BW™ Clip4 Multi-Gas Detector: Wearable four gas detector that runs for two years with no charging, no battery replacement and no sensor swap. It monitors the four gases most often required for confined space and general industrial work, then is retired at end of life.
• Honeywell BW™ Flex: Portable multi gas detector with a choice of more than fifteen sensors covering up to four hazards at once. A large high resolution display shows live readings in a wide range of languages, which suits mixed workforces on industrial sites.
• Honeywell BW™ Flex4 Multi Gas Detector: Four gas portable detector in the Honeywell BW Flex range, monitoring oxygen, combustibles, carbon monoxide and hydrogen sulphide. It is aimed at confined space entry and routine industrial work where a rugged and simple instrument is wanted.
• Honeywell BW™ Icon Multi Gas Detector: Fixed life two year four gas detector with an icon based display instead of numeric readings, so workers act on a clear symbol rather than interpret a figure. No sensor or battery replacement is needed over its service life.
• Honeywell BW™ MicroClip Series Multi-Gas Detector: Compact four gas portable detector for confined space entry and general industrial use, offered in XL and X3 versions. It is small and simple to operate, with long runtime between charges and low cost of ownership.
• Honeywell BW™ Max XT II Multi Gas Detector: Four gas detector with an integrated SmartSample pump for pre entry testing of confined spaces. One button operation keeps compliance testing simple, and the motor draws samples from remote points before anyone enters.
• Honeywell BW™ Ultra Multi Gas Detector: Five gas pumped detector built for confined space entry, sampling before and after workers go in. It covers the four gases normally required plus a fifth channel such as a photoionisation sensor, with connectivity for live status.
• MicroRAE Wireless 4-gas monitor: Wireless diffusion monitor measuring up to four gases at once, including hydrogen sulphide, carbon monoxide, oxygen and combustibles. Several wireless options send readings, location and alarm status to ConneXt and Safety Communicator systems.
• MultiPro Multi-Gas Detector: Compact four gas detector for confined space work with one button operation and calibration, an LCD readout, audible and visual alarms and an event logger. An optional sample draw pump allows pre entry testing.
• MultiRAE Lite Pumped ATX PID LEL Portable Multi Gas Monitor: Pumped six gas portable monitor combining a photoionization detector, a combustible LEL channel and electrochemical sensors. It is used for confined space entry and leak survey work where volatile organic compounds have to be measured alongside the standard four gases.
• MultiRAE Lite Pumped Multi Gas Detector: Pumped multi gas monitor covering up to six gases from a choice of more than 25 sensors, including VOC, combustible, toxic and oxygen channels. It suits personal protection and leak detection where the mix of hazards varies by job.
• MultiRAE Pro Portable Multi Gas Monitor: Wireless monitor that covers chemical threats and gamma radiation in one instrument, with parts per billion precision. Threat and alarm data can be transmitted live to a command station, and 25 interchangeable sensors are available.
• QRAE 3 PGM-2560 Series Gas Detector Pumped: Pumped one to four sensor monitor giving continuous exposure measurement of oxygen, combustibles and toxic gases including hydrogen sulphide, carbon monoxide, sulphur dioxide and hydrogen cyanide. Built for workers and responders in hazardous areas.
• QRAE 3 Wireless 4-Gas Monitor: Rugged one to four sensor gas monitor with wireless communication, available in pumped or diffusion form. Live readings and alarm status can be viewed remotely, which keeps a safety officer informed without entering the hot zone.
• UltraRAE 3000 + PID10.6 Portable Handheld Computer: UltraRAE 3000 + supplied with the 10.6 eV photoionization lamp, the general purpose choice for volatile organic compound survey, industrial hygiene and benzene specific work. Datalogging runs for six months at one minute intervals.
• GasAlertMicro 5 Series Multi-Gas Detector: Portable detector covering up to five atmospheric hazards including oxygen, combustibles and toxic gases. Alkaline or rechargeable battery packs and an optional pump make it flexible across confined space and general industrial duties.
• MiniRAE 3000 + Portable Handheld VOC Monitor: Handheld photoionisation VOC monitor for industrial hygiene, leak detection and hazardous material response. It offers a wide detection range, a three second response, correction factors for over 200 compounds and a self cleaning sensor.
• QRAE 3 PGM-2500 Series Gas Detector Pumped (Wireless): Wireless pumped version of the QRAE 3 one to four sensor monitor, covering oxygen, combustibles and toxic gases. Readings and alarm status, including man down, are sent to ProRAE Guardian or the EchoView Host mini controller for remote visibility.
• MiniRAE Lite + Portable Handheld VOC Monitor: Handheld photoionisation monitor for volatile organic compounds during leak detection, environmental clean up and remediation. The pump draws samples from up to 100 feet away, and the rugged housing suits work outside the plant fence.
• UltraRAE 3000 + PID11.7 Handheld Computer: UltraRAE 3000 + supplied with the 11.7 eV photoionization lamp, which raises the ionization energy so that compounds outside the reach of the standard lamp can be measured. It keeps the same pump, datalogging and wireless options as the rest of the range.
• MultiRAE Portable Multi Gas Monitor: Wireless portable chemical detector taking up to six gas sensors at once, with 25 field changeable sensor options covering LEL, PID, NDIR and exotic gases. Readings and alarm status are available live from any location.
• MultiRAE (Model PGM-6228) Portable Multi Gas Monitor: MultiRAE model PGM-6228, the diffusion configuration of the six sensor portable monitor. Sensors are field interchangeable across 25 options including PID, NDIR and exotic channels, and five local and remote alarms include man down.
• ppbRAE 3000 + Portable Handheld VOC Monitor: Handheld VOC monitor built around a third generation photoionisation detector for parts per billion measurement. Correction factors for more than 200 compounds are built in, and it is widely used in hazardous material and oil and gas response work.
• UltraRAE 3000 + PID9.8 Portable Handheld Computer: UltraRAE 3000 + supplied with the 9.8 eV photoionization lamp, for compound specific measurement of benzene and butadiene as well as total volatile organic compounds. The narrower lamp energy reduces response to interfering compounds during survey work.
• UltraRAE 3000 + Portable Handheld Compound Specific VOC Monitor: Compound specific photoionisation monitor that works in broad VOC mode or with a separation tube for benzene specific measurement. It is used for entry pre-screening during plant maintenance, spill response and downstream refinery monitoring.
• MultiRAE Pro (Model PGM-6248) Portable Multi Gas Monitor: MultiRAE Pro model PGM-6248, the configuration that adds a gamma radiation channel to the six sensor gas monitor. It is used by responders who need chemical and radiological screening from a single instrument.
• BW™ Clip Series 2 Year Real Time Single Gas Detector: Maintenance free single gas detector with a live concentration readout and a fixed two year service life. It is switched on once and runs continuously, with no sensor replacement, battery change or charging in between.
• IntelliDoX Automated instrument management system: Docking system that combines smart modules with device management software to automate bump testing, calibration and record keeping. It supports BW Solo, BW Ultra, BW Max XT II, BW Clip Series, BW Clip4 and BW MicroClip Series detectors.
• BW™ Clip Series 2 Year Single Gas Detector: Single gas detector with a fixed two year run time that needs no sensor replacement, battery change or charging. It is switched on at first use and runs continuously until the end of its service life.
• BW™ Clip Series 3 Year Single Gas Detector: Single gas detector with a fixed three year run time and no maintenance during service. Turn it on once and it monitors continuously, which removes charging routines and sensor swaps from the daily workflow.
• Honeywell BW™ Solo Single Gas Detector: Serviceable single gas detector with Bluetooth Low Energy connectivity for live visibility of worker and instrument status. Data from the detector or its docking station can be managed in the Honeywell Safety Suite software platform.
• Honeywell BW™ Solo Lite Single Gas Detector: Entry level version of the serviceable BW Solo single gas detector, with replaceable sensor and battery. It gives the same core alarm behaviour and docking compatibility for sites that do not need wireless connectivity.
• Honeywell BW™ Solo Standard Single Gas Detector: Standard, non wireless version of the Honeywell BW Solo single gas detector. It covers up to 14 user selected common and exotic gases, and the sensor, filter and battery can all be replaced in the field rather than returning the unit.
• BW™ Clip Series 3 Year Real Time Single Gas Detector: Maintenance free single gas detector with a live concentration display and a fixed three year service life. It runs continuously from first activation with no charging, battery change or sensor replacement.
• ToxiPro® Single Gas Detector: Reusable single gas detector with a field replaceable sensor and three visual alarm windows carrying both yellow warning and red danger LEDs. It forms part of the IQ Management System for docking, record keeping and fleet control.
• Honeywell BW™ Solo Wireless Single Gas Detector: Wireless version of the serviceable BW Solo single gas detector, sending status and alarm data over Bluetooth Low Energy. Safety teams can see who is in alarm and where, which shortens the time to respond to an incident.
• ToxiRAE Pro CO2 Monitor: Personal wireless carbon dioxide monitor for compliance testing and periodic checks. Readings can be followed remotely from a command station, which suits work in cellars, breweries and other spaces where CO2 can accumulate.
• ToxiRAE Pro Family Gas Monitor: Family of wireless personal single gas monitors sharing one user interface, calibration routine and accessory set. Covering common toxic industrial chemicals, oxygen, combustibles and VOCs, it simplifies training and spares across a plant.
• ToxiRAE Pro Gas Monitor: Compact personal wireless monitor for toxic gases and oxygen with five way local and remote alarms, including man down. Sensors are easily swapped so one instrument can be moved between different gas hazards.
• ToxiRAE Pro LEL Gas Monitor: Personal wireless monitor for combustible gas measured against the lower explosive limit. It carries a large on-board gas library with 55 built in correction factors and sends live proximity to LEL data back to a command station.
• ToxiRAE Pro VOC Single Gas Monitor: Personal wireless photoionisation monitor covering over 300 volatile organic compounds. An on-board library of 190 correction factors reads gases in equivalent units, and readings can be watched remotely from a command station.
• ToxiRAE Pro CO2 Safe Area Personal Monitor: Personal carbon dioxide monitor using a non dispersive infrared sensor, for safe area use in wineries, breweries, landfill work and indoor air quality checks. Honeywell state that this unit cannot be used in a hazardous area.
• AreaRAE Pro Portable Gas Monitor: Transportable wireless area monitor covering up to seven threats, including gamma radiation, VOCs, combustibles, toxics and oxygen. It is deployed around an incident or work area to give responders live readings from a distance.
• MeshGuard CO2 Wireless Gas Detector: Rapidly deployable wireless infrared carbon dioxide monitor for critical environments. Readings pass over the same self healing mesh network as other MeshGuard monitors to a controller for remote display and alarm.
• Honeywell BW™ RigRAT Transportable Multi-gas Area Monitor: Transportable multi gas area monitor placed near a work area to warn nearby workers of gas hazards. It supports wireless perimeter monitoring, works with Touchpoint Plus and can run on line power for extended field deployment.
• AreaRAE Plus/Pro Multi-Gas Detector: Transportable area monitor covering up to seven threats including VOCs, combustibles, toxics and oxygen, with an optional meteorological sensor for wind speed, direction and humidity. Readings are transmitted live for incident management.
• MeshGuard LEL Wireless Gas Detector: Wireless combustible gas monitor that measures the lower explosive limit and joins a self healing mesh network with other monitors and a controller. Readings appear on the local LCD and drive integrated audible and visual alarms.
• MeshGuard Wireless Gas Detector: Rapidly deployable wireless gas detector for temporary monitoring in hazardous environments. Units form a self healing mesh network with a controller, so a monitoring layout can be set up and moved without running cable.
• AreaRAE Pro PID (Photoionization Detector) Sensors: Photoionization sensor option for the AreaRAE Pro transportable area monitor, giving parts per billion measurement of volatile organic compounds. It fits one of the monitor's sensor slots alongside the toxic, oxygen, combustible and gamma channels.
• AreaRAE Pro RAEMet Sensor: Weather sensor module for the AreaRAE Pro transportable area monitor. It adds local wind speed, wind direction, temperature and humidity readings to the gas data sent back to the command station, which helps responders judge plume movement.
• BW™ Replacement Sensors: Replacement electrochemical and catalytic sensor range for Honeywell BW portable detectors. Sensors are ordered by gas and by host instrument, so a detector already in service can be kept in calibration without replacing the whole unit.
• Calibration Gas Cl2 HCl HCN PH3: Calibration gas for chlorine, hydrogen chloride, hydrogen cyanide and phosphine sensors, covering the reactive species used in semiconductor and chemical plant. Cylinders run from 11 litres to 103 litres and are available as portable kits.
• Calibration Gas CO: Carbon monoxide calibration gas in aluminium cylinders for spanning CO sensors in Honeywell fixed and portable detectors. Cylinders run from 11 litres to 103 litres and take either a demand flow or a constant flow regulator.
• Calibration Gas H2S: Hydrogen sulphide calibration gas for spanning H2S sensors in Honeywell fixed and portable detectors. Cylinders run from 11 litres to 103 litres and can be supplied as a portable field kit with a demand flow or constant flow regulator.
• Calibration Gas NOx/SOx: Nitrogen oxide and sulphur oxide calibration gas for spanning NOx and SOx sensor channels. Cylinders run from 11 litres to 103 litres and can be ordered as portable field kits with either a demand flow or a constant flow regulator.
• Calibration Gases 2 Gas: Two gas calibration mixtures for Honeywell portable monitors, letting two sensor channels be spanned from one cylinder. Cylinders run from 11 litres to 103 litres and are available as portable field kits with a demand flow or constant flow regulator.
• Calibration Gases 4 Gas: Four gas calibration mixtures for confined space monitors, typically covering combustibles, oxygen, carbon monoxide and hydrogen sulphide in one cylinder. Cylinders run from 11 litres to 103 litres and are available as portable field kits.
• Calibration Gases: Calibration gas cylinders for Honeywell RAE portable monitors, in single gas and multi gas mixtures. Cylinders run from 11 litres to 103 litres and can be ordered as portable field kits with either a demand flow or a constant flow regulator.
• GasAlertMicroClip X3 1-Gas Detector Black: Honeywell BW MicroClip Series 1 gas portable detector in a black housing, monitoring 1 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 1-Gas Detector Yellow: Honeywell BW MicroClip Series 1 gas portable detector in a yellow housing, monitoring 1 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 2-Gas Detector Black: Honeywell BW MicroClip Series 2 gas portable detector in a black housing, monitoring 2 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 2-Gas Detector Yellow: Honeywell BW MicroClip Series 2 gas portable detector in a yellow housing, monitoring 2 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 3-Gas Detector Black: Honeywell BW MicroClip Series 3 gas portable detector in a black housing, monitoring 3 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 3-Gas Detector Yellow: Honeywell BW MicroClip Series 3 gas portable detector in a yellow housing, monitoring 3 of the four gases in the MicroClip range. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 4-Gas Detector Black: Honeywell BW MicroClip Series 4 gas portable detector in a black housing, monitoring oxygen, combustibles, carbon monoxide and hydrogen sulphide. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip X3 4-Gas Detector Yellow: Honeywell BW MicroClip Series 4 gas portable detector in a yellow housing, monitoring oxygen, combustibles, carbon monoxide and hydrogen sulphide. The X3 model carries a three year warranty and the updated O2 sensor, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 1-Gas Detector Black: Honeywell BW MicroClip Series 1 gas portable detector in a black housing, monitoring 1 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 1-Gas Detector Yellow: Honeywell BW MicroClip Series 1 gas portable detector in a yellow housing, monitoring 1 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 2-Gas Detector Black: Honeywell BW MicroClip Series 2 gas portable detector in a black housing, monitoring 2 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 2-Gas Detector Yellow: Honeywell BW MicroClip Series 2 gas portable detector in a yellow housing, monitoring 2 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 3-Gas Detector Black: Honeywell BW MicroClip Series 3 gas portable detector in a black housing, monitoring 3 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 3-Gas Detector Yellow: Honeywell BW MicroClip Series 3 gas portable detector in a yellow housing, monitoring 3 of the four gases in the MicroClip range. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 4-Gas Detector Black: Honeywell BW MicroClip Series 4 gas portable detector in a black housing, monitoring oxygen, combustibles, carbon monoxide and hydrogen sulphide. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• GasAlertMicroClip XL 4-Gas Detector Yellow: Honeywell BW MicroClip Series 4 gas portable detector in a yellow housing, monitoring oxygen, combustibles, carbon monoxide and hydrogen sulphide. The XL model carries a two year warranty, with an IP68 rated case and one button operation.
• Calibration Gas H2: Hydrogen calibration gas for spanning hydrogen sensors and for cross checking catalytic combustible channels. Cylinders run from 11 litres to 103 litres and can be ordered as portable field kits with a demand flow or constant flow regulator.
• Honeywell Colorimetric Tubes A-G: Single use colorimetric detection tubes for compounds beginning A to G, read with a hand pump. The tube changes colour in proportion to the gas concentration present, so a spot measurement needs no calibration and no maintenance.
• Honeywell Colorimetric Tubes H-M: Single use colorimetric detection tubes for compounds beginning H to M, read with a hand pump. The tube changes colour in proportion to the gas concentration present, giving a compound specific spot reading without an electronic instrument.
• Honeywell Colorimetric Tubes N-Z: Single use colorimetric detection tubes for compounds beginning N to Z, read with a hand pump. The tube changes colour in proportion to the gas concentration present, which suits occasional checks on substances no fixed sensor covers.
• MeshGuard Sensors: Spare and replacement sensors for the MeshGuard wireless area detection range. Each sensor plugs into the MeshGuard head so a deployed mesh can be re-tasked to a different gas hazard without changing the radio or the battery pack.
• RAE Replacement Sensors: Replacement sensor range for Honeywell RAE Systems portable and transportable gas monitors. Cartridges cover the toxic, oxygen, combustible and photoionization channels used across the MultiRAE, QRAE, ToxiRAE and AreaRAE instruments.
• Replacement Sensors (Multiple Products): Replacement sensors shared across more than one Honeywell instrument range, covering both Honeywell BW and Honeywell RAE Systems monitors. Ordering from the common list avoids holding separate stock for each detector family.
• Sensepoint Spare Sensors: Range of toxic and flammable replacement sensors for the Sensepoint family of fixed gas detectors. Sensors are supplied pre-configured for the gas they monitor, which keeps recalibration and downtime at the detector head short.
• Sensepoint XCL/XRL Replacement Sensors: Replacement sensor cartridges for the Sensepoint XCL and Sensepoint XRL fixed detectors. Changing a cartridge restores the detector to its published performance without removing the transmitter from the wall or rewiring the loop.
• Series 3000 Instruments and Sensors: Loop powered transmitter range for toxic and oxygen hazards in potentially explosive atmospheres, in MkII flameproof and MkIII intrinsically safe versions. Smart sensors are supplied pre-configured and can be hot swapped without removing power.
• Safety Suite: Software platform for managing a gas detector fleet and monitoring worker safety in one place. It brings connected devices, analytics and workflow automation together so that plant, remote and emergency response teams can track exposure, compliance and instrument status.
• Honeywell Safety Suite 2.0: Second generation of the Honeywell Safety Suite fleet management platform, adding an exposure dashboard to the device, compliance and analytics tools. It secures management of the gas detection fleet and worker safety monitoring from one interface.
• Experion GMS: Experion based SCADA platform that gives a centralised view of gas detection data and alarm management across a site. It integrates natively with Honeywell PLCs and gas detectors and takes direct data from the Vertex OPC server.
• GDVS - Gas Detection Visualisation Solutions: Software and hardware package that gives remote access to live gas detection data from Honeywell controllers and transmitters. It shows transmitter status and gas concentration trend on a PC, tablet or smartphone using atvise SCADA visualisation.
• RAELink 3 Wireless Transmitter: Portable wireless router with GPS that sends sensor and alarm data from RAE Systems portable monitors back to a ProRAE Guardian base station. It can be programmed as a host, a remote router or a signal repeater, and reports monitor location as well as readings.
• RAEPoint Wireless Infrastructure: Fixed head wireless device that works as a DC powered explosion proof mesh router or as a remote relay extending network range. Separate versions suit fixed MeshGuard detectors or wireless portables such as the MultiRAE and ToxiRAE Pro.
• Honeywell RAEPoint Fixed Wireless Router: Permanently mounted wireless router that carries gas monitor data to a Safety Suite host controller or an EchoView Host handheld controller. One unit supports up to 50 compatible monitors and is certified for Class I, Division 1 areas.
• MeshGuard Wireless Infrastructure: Infrastructure hardware for the MeshGuard rapidly deployable gas detection system, covering the radio components that carry detector data across a temporary site network. Units are built for hazardous area use in a stainless steel housing.
• MeshGuard PowerPak SolarPak: Power and solar power packs for the MeshGuard rapidly deployable gas detection system, so a mesh can run where no mains supply exists. The packs mount to a pole or wall and are built for hazardous area use.
• MeshGuard Stainless Steel Compliance Kit: Stainless steel compliance kit for the MeshGuard rapidly deployable gas detection system, supplied for installations that must meet a stainless construction requirement. MeshGuard itself is intended for hazardous environments.
• Honeywell Central Hub: Connectivity gateway that collects gas sensor data over long range low power radio and reports it to Honeywell Safety Suite in real time. Several hubs can be combined to cover a wide area, and the uplink can be Ethernet, Wi-Fi or cellular.
• Honeywell BW™ Connect BLE Adapter and Rugged Smart Hand Held Device: Bluetooth adapter that turns an existing Honeywell BW gas detector into a wireless monitoring device. It clips to the detector, pairs with a smartphone and works with the Honeywell Safety Communicator App to give live visibility of worker status and alarms.
• AreaRAE Plus Rapid Deployment Kit (RDK): Kit that packs four GPS enabled AreaRAE Plus monitors with a built in RAELink3 wireless router and the accessories needed for field operation. It is meant for teams that have to stand up an area monitoring network quickly at an incident.
• AreaRAE Pro Rapid Deployment Kit (RDK): Rapid deployment kit built around four GPS enabled AreaRAE Pro monitors, a RAEMet weather sensor and a built in RAELink3 wireless router, with gamma radiation detection included. It covers chemical and radiological screening from one case.
• RDK Host Preconfigured Laptop Controller: Turnkey wireless host controller with ProRAE Guardian pre-installed on a laptop and a RAELink 3 transmitter, packed in a ruggedised case. It needs no assembly and receives data from up to 64 remote wireless monitors on a live map.
• Honeywell Handheld Pump: Lightweight pump that adds remote sampling to compatible portable diffusion gas monitors, for spot checks, clearing and extended sampling. It uses the standard flow adaptor already supplied with instruments such as the BW Flex 4, BW Clip 4 and BW Solo.
• Honeywell Model LP-1200 Piston Hand Pump: Piston hand pump used with Honeywell colorimetric detection tubes for on the spot measurement of specific toxic and combustible substances. The spring-less piston draws an accurate sample and the solid metal body can be worked while wearing gloves.
• 301R Relay Module: Relay output module for the 201C and 301C controllers, providing eight double pole double throw relays for indirect activation of fans, louvres and similar plant at programmable alarm levels. It can sit anywhere on the gas detection network.
• Audio and Visual Alarm Devices: Range of audible and visual alarm devices for indoor and outdoor use. Combined with Honeywell fixed point gas monitoring equipment they give operators a clear warning that a flammable or toxic gas hazard is present in the area.
• OELD Smart Junction Box: Hazardous location certified junction box for Searchpoint Optima Plus and Searchline Excel detectors. It gives a local visual status indication and a Bluetooth Low Energy interface for configuration and maintenance from a mobile device.
• Calibration and Maintenance Accessories (AutoRAE 2 System): Calibration and maintenance accessory range for the AutoRAE 2 automatic bump test and calibration system. It covers the cradles, adaptors and consumable items needed to bump test and calibrate RAE Systems gas monitors in a standalone or networked setup.
• Calibration, Maintenance accessories and Replacement Parts: Calibration and maintenance accessory range published by Honeywell alongside their portable gas monitors. It groups the adaptors, cups and related items used when bump testing or calibrating an instrument, together with the parts consumed in that work.
• QRAE 3 Calibration Accessory: Calibration accessory range for the QRAE 3 portable gas monitor, covering the adaptors and fittings needed to connect a calibration gas cylinder to the instrument for bump testing and span calibration.
• AreaRAE Pro Calibration and Maintenance Accessories: Calibration and maintenance accessory range for the AreaRAE Pro transportable area monitor. It covers the adaptors and service items used when bump testing, calibrating and maintaining the monitor between deployments.
• Posi3 USB: Computerised NFPA compliant breathing machine that tests self contained breathing apparatus, checking facepiece integrity, regulator performance, pressure accuracy, alarms and breathing resistance. It connects to a Windows PC by USB and stores results automatically.
• ACM 150G2 Gas Monitoring System: FTIR based gas monitoring system for semiconductor and industrial process exhaust. The redesigned bench lowers the detectable limit for many gases, and the operator interface shows proof of response for each measurement point.
• Vertex™ Edge Toxic gas monitoring system: Centralised Chemcassette monitoring cabinet holding up to nine analysers, each with eight points of detection. It covers virtually every gas used in a semiconductor fab down to parts per billion, with gas readings, alarms and events on one screen.
• Vertex™ Multi-Point Toxic Gas Monitoring System: Continuous Chemcassette monitoring system scaling to 72 points of gas detection. Analysers, optics and software are combined in one cabinet so a fab can start small and add points as the monitoring requirement grows.
• Vertex™ M Toxic Gas Monitoring System: Chemcassette monitoring system covering eight to 24 points of continuous gas detection, with built in redundancy to protect against downtime. Sampling points can be added as monitoring needs change without replacing the cabinet.
• Chemcassette Tapes: Colorimetric paper tape consumable used by Honeywell Chemcassette gas analysers. The chemically treated tape reacts within seconds to parts per billion levels of many hazardous gases and leaves a visible stain as physical evidence of the event.
• Midas® Gas Detector: Fixed extractive single point gas detector that draws a sample from up to 30 metres away to a sensor cartridge inside the chassis. Over 35 toxic, ambient and flammable gases are covered, with Power over Ethernet, Modbus TCP and a browser interface.
• CM4 Toxic Gas Monitor: Four point Chemcassette monitor for low level toxic gases in semiconductor, pharmaceutical and chemical plant. Quarter inch sample tubing keeps intrusion into process areas, ducts and gas cabinets to a minimum, and several signal outputs are available.
• Midas®-M 4 in 1 Multi gas detector: Fixed extractive single point detector that carries up to four sensor cartridges in one chassis and covers more than 30 gases. It samples locally or from a remote point, which suits semiconductor tool and utility monitoring where space is limited.
• SPM Flex Gas Detector: Portable single point Chemcassette tape detector for low level toxic gases. It is used for leak investigation, emergency response and routine tool maintenance, and integrates with plant systems when a temporary monitoring point is needed.
• Midas®S2 Gas Detector: Fixed extractive single point transmitter that draws a sample locally or from a remote point to a sensor cartridge. A wide cartridge range covers toxic, flammable and oxygen hazards found in semiconductor fabs, light manufacturing and research laboratories.
• Toxic Gas Monitor VC4: Four point Chemcassette gas detection system for highly toxic gases down to parts per billion. The reaction leaves a clear stain on the treated tape, giving a visible record of the event alongside the electronic reading.
• Midas® Sensor Cartridge: Honeywell list the Midas sensor cartridge under air quality sensors in their building automation catalogue. The page carries a single technical statement, that each Midas sensor is potentially cross sensitive to other gases, which may cause a gas reading when the sensor is exposed to gases other than the one it was designated for. Certifications are the only other data published, and no gas list, range, lifetime or part number is given. The page shows no product photograph.