Thermodynamics Lab in Bangladesh

EDIBON teaching and research units for the thermodynamics laboratory, supplied, installed and commissioned in Bangladesh by Vvon with faculty training included. 47 units available.

47 products from 1 manufacturer: EDIBON.

Products

• TBCF: Bomb Calorimeter — EDIBON: Constant volume calorimeter for determining the calorific value of solid and liquid fuel samples. The stainless steel bomb is charged with oxygen and fired electrically inside a water filled vessel, while a motor driven stirrer and a precision thermometer follow the temperature rise.
• TCESC: Computer Controlled Separating and Throttling Calorimeter — EDIBON: Unit for determining the moisture content and dryness fraction of steam. Wet steam is first separated by a series of obtuse angle changes of direction, then throttled into an expansion chamber, with pressure and temperature measured at each stage and the condensate weighed.
• TECMC: Computer Controlled Marcet Boiler Unit — EDIBON: Marcet boiler for the experimental study of the relationship between pressure and temperature of saturated steam in equilibrium with water. Students plot the saturation curve, compare it with published steam tables and derive the Clausius Clapeyron equation.
• TEPGC: Computer Controlled Expansion Processes of a Perfect Gas Unit — EDIBON: Two connected methacrylate vessels, one pressurised and one under vacuum, used to demonstrate expansion and compression of a perfect gas. Fast and slow expansions are compared, giving practical work on the first and second laws of thermodynamics.
• TLBGC: Computer Controlled Gas Laws Unit (Boyle and Gay-Lussac Laws) — EDIBON: Bench unit that demonstrates two fundamental gas laws using air as the test gas. One transparent vessel gives the isochoric change of state by electrical heating, the second gives the isothermal change of state using an oil piston driven by a compressor and vacuum pump.
• TSPC: Computer Controlled Saturation Pressure Unit — EDIBON: Water boiler with a sight glass and a throttling calorimeter, used to measure the relationship between saturation temperature and pressure and to determine the dryness fraction of the steam produced. Boiling patterns at the water surface can be observed directly.
• TVCC: Computer Controlled Combustion Laboratory Unit — EDIBON: Burner and water cooled combustion chamber for the study of liquid and gaseous fuel combustion. Students vary the air to fuel ratio and measure its effect on flame characteristics, combustion efficiency, flue gas composition and the energy balance.
• TVPLC: Computer Controlled Flame Propagation and Stability Unit — EDIBON: Vertical burner unit that produces different flame types by varying the fuel and comburent mixture, so that gaseous fuels can be compared. A separate propagation accessory lets students watch a flame travel along a transparent hose ignited by a spark plug.
• TMT: Temperature Measurement Unit — EDIBON: Teaching unit that compares several temperature measuring devices and their accuracy. It covers thermometric properties, the Peltier and Seebeck thermoelectric effects, the laws of intermediate metals and temperatures, and series or parallel thermocouple arrangements.
• TMHA: Air Humidity Measurement Unit — EDIBON: Stainless steel duct fitted with several humidity instruments so that their accuracy can be compared. The duct can be humidified with an ultrasonic atomiser and dehumidified with a Peltier element, and a variable flow fan shows the effect of airflow on each instrument.
• TFTC: Computer Controlled Nozzle Performance Test Unit — EDIBON: Pressure chamber unit for investigating nozzle kinetic energy and thrust from a laboratory compressed air supply. Students demonstrate choking, measure jet reaction and specific thrust, and compare the actual mass flow rate with the theoretical value.
• TPT: Nozzle Pressure Distribution Unit — EDIBON: Unit for investigating pressure distribution and mass flow rate in convergent and convergent divergent nozzles. Compressed air is regulated at the nozzle inlet and outlet, and each pressure tapping has its own manometer so the choking effect can be shown visually.
• TMSB: Stirling Motor — EDIBON: Alfa type Stirling engine that converts thermal energy into mechanical energy and can drive an electrical generator. The four phases of the ideal Stirling cycle are followed on two power pistons in separate hot and cold cylinders linked through a regenerator.
• TMTC: Computer Controlled Temperature Measurement Unit — EDIBON: Designed to study the different ways in which temperature can be measured, the "TMTC" Computer Controlled Temperature Measurement Unit is a laboratory-scale unit.
• TRLB: Recycle Loops Unit — EDIBON: Designed by EDIBON, the "TRLB" Recycle Loops Unit was created to demonstrate the basic operating principles of recycle loops.
• TRLC: Computer Controlled Recycle Loops Unit — EDIBON: Designed by EDIBON, the "TRLC" Computer Controlled Recycle Loops Unit serves to demonstrate the basic operating principles of recycle loops.
• DFCM: Unit to Study a Filter Drier Cutaway Model — EDIBON: Designed by EDIBON, the "DFCM" Unit to Study a Filter Drier Cutaway Model allows students to visualise the inner parts of a (element), evaluate how the parts relate to each other accurately, and understand their function.
• GMCM: Unit to Study a Gas Meter Cutaway Model — EDIBON: With the "GMCM" Unit to Study a Gas Meter Cutaway Model, students can visualise the inner parts of a gas meter, evaluate accurately how they relate to each other, and understand their function.
• HCCM: Unit to Study a Hermetic Refrigerant Compressor Cutaway Model — EDIBON: With the "HCCM" Unit to Study a Hermetic Refrigerant Compressor Cutaway Model, students can visualise the inner parts of a compressor, evaluate accurately how they relate to each other, and understand their function.
• HOSCM: Unit to Study a Helical Oil Separator Cutaway Model — EDIBON: With the "HOSCM" Unit to Study a Helical Oil Separator Cutaway Model, students can visualise the inner parts of a liquid separator, evaluate accurately how they relate to each other, and understand their function.
• LSCM: Unit to Study a Liquid Separator Cutaway Model — EDIBON: Designed by EDIBON, the "LSCM" Unit to Study a Liquid Separator Cutaway Model allows students to visualise the inner parts of a liquid separator, evaluate how they relate to each other accurately, and understand their function.
• OCCM: Unit to Study an Open Refrigerant Compressor Cutaway Model — EDIBON: With the "HCCM" Unit to Study an Open Refrigerant Compressor Cutaway Model, students can visualise the inner parts of an open compressor, evaluate accurately how they relate to each other, and understand their function.
• SCCM: Unit to Study a Semi-Hermetic Refrigerant Compressor Cutaway Model — EDIBON: With the "SCCM" Unit to Study a Semi-hermetic Compressor Cutaway Model, students can visualise the inner parts of a compressor, evaluate accurately how they relate to each other, and understand their function.
• SHICM: Unit to Study a Sight Glass with Humidity Indicator Cutaway Model — EDIBON: Designed by EDIBON, the "SHICM" Unit to Study a Sight Glass with Humidity Indicator Cutaway Model allows students to visualise the inner parts of a sight glass, evaluate how they relate to each other accurately, and understand their function.
• GBT: Forced Draft Gas Burner Unit — EDIBON: The "GBT" Forced Air Gas Burner Trainer supports study of the arrangement, measuring elements and safety devices that a forced air gas burner system requires.
• GHST: Domestic Gas Supply Experimentation Unit — EDIBON: Designed by EDIBON, the "GHST" Gas Home Supply Trainer is a teaching unit in which the elements normally used in any domestic gas installation are arranged on the front panel of the unit, as in a real installation.
• IGHT: Instantaneous Gas Heater Experimentation Unit — EDIBON: Designed by EDIBON, the "IGHT" Instantaneous Gas Heater Experimentation Unit allows users to study the operation, installation and assembly of this type of device. It also allows faults to be simulated, so they can be analysed and repaired.
• MRST: Measurement and Regulation Station Unit — EDIBON: Designed by EDIBON, the "MRST" Measurement and Regulation Station Trainer is a bench-top unit that is totally accessible.
• RT: Radiators Training Unit — EDIBON: Designed by EDIBON, the "RT" Radiators Training Unit is intended for the study of hot water heating systems.
• TAMR: Assembly and Maintenance in Refrigeration Systems Unit — EDIBON: The "TAMR" Assembly and Maintenance in Refrigeration Systems Unit has been designed for learning and understanding the different parts of a basic compression refrigeration system. It also supports learning the assembly and startup procedure for a compression refrigeration system with an air condenser and evaporator.
• TECR: Electrical Connection of Refrigerant Compressors Unit — EDIBON: Designed by EDIBON, the "TECR" Electrical Connection of Refrigerant Compressors Unit allows students to analyse these aspects, giving them a view oriented to real refrigeration systems, since all the elements are operated and tested with mains voltage.
• TEFA: Electrical Faults in Air Conditioning Systems Unit — EDIBON: Designed by EDIBON, the "TEFA" Electrical Faults in Air Conditioning Systems Unit shows the most important electrical faults in air conditioning systems. It simulates a simple air conditioning system with compressor, fan and thermostat, and enables investigation of key electrical components from air conditioning technology.
• TEIR: Electrical Installations in Refrigeration Systems Unit — EDIBON: Designed by EDIBON, the "TEIR" Electrical Installations in Refrigeration Systems Unit teaches students about different circuits and electrical devices associated with the refrigeration field, how to carry out the wiring of these types of installations, how the refrigeration components are mounted, and how they interact with each other.
• TEIS: Sanitary Fittings Training Unit — EDIBON: Designed by EDIBON, the "TEIS" Sanitary Fittings Training Unit is intended for training in the plumbing sector.
• TELT: Pipe Cleaning Training Unit — EDIBON: Designed by EDIBON, the "TELT" Pipe Cleaning Training Unit simulates a real house piping system; original components used in plumbing systems are therefore employed.
• TEMT: Temperature Measurement Training Unit — EDIBON: Designed by EDIBON, the "TEMT" Temperature Measurement Training Unit allows comparison of the response of several temperature measuring devices across different flows and different installation positions.
• TEV3V: Three-Way Mixing Valve Training Unit — EDIBON: The "TEV3V" Three-Way Mixing Valve Training Unit allows the function of a three-way mixing valve in a hot water heating system to be demonstrated.
• TEV4V: Four-Way Mixing Valve Training Unit — EDIBON: The "TEV4V" Four-Way Mixing Valve Training Unit allows the function of a four-way mixing valve in a hot water heating system to be demonstrated.
• TIAP: Drinking Water Installation Unit — EDIBON: Designed by EDIBON, the "TIAP" Drinking Water Installation Unit demonstrates domestic water heating starting from the cold water supply.
• TIR: Introduction to Refrigeration Unit — EDIBON: Designed by EDIBON, the "TIR" Introduction to Refrigeration Unit uses simple and clear experiments to familiarise users with the operation and handling of a refrigeration system, offering a basic introduction to refrigeration.
• TPAP: Protection of Drinking Water Training Unit — EDIBON: Designed by EDIBON, the "TPAP" Protection of Drinking Water Training Unit is intended for studying cases where the drinking water system becomes contaminated with wastewater. In particular, it is designed for training students in the plumbing sector.
• TRAMC: Computer Controlled Refrigeration and Air Conditioning Modular Unit — EDIBON: Designed by EDIBON, the "TRAMC" Computer Controlled Refrigeration and Air Conditioning Modular Unit is modular, consisting of the TRAMC Unit Base, "TRAMC-UB", which can be complemented with different optional models to form different complete compression refrigeration circuits.
• TRAMC/1: Home Refrigeration Model — EDIBON: The "TRAMC/1" Home Refrigeration Model is made up of a refrigeration chamber with a heater as the refrigeration load, an evaporator, a fan, and two expansion elements, a capillary tube or an expansion valve, selected using a solenoid valve.
• TRAMC/2: Refrigeration System with Refrigeration and Freezing Stage Model — EDIBON: The "TRAMC/2" Refrigeration System with Refrigeration and Freezing Stage Model is made up of two separate refrigeration chambers, each with an evaporator able to work in series or in parallel.
• TRAMC/3: Simple Air Conditioning System Model for Room Cooling — EDIBON: Within the "TRAMC" training system for refrigeration and air conditioning engineering, the "TRAMC/3" provides a Simple Air Conditioning System Model for Room Cooling.
• TRAMC/4: Complete Air Conditioning System Model — EDIBON: Belonging to the "TRAMC" training system for refrigeration and air conditioning engineering, the "TRAMC/4" Complete Air Conditioning System Model is one of its models.
• TSID: Sewerage Unit — EDIBON: The "TSID" Sewerage Unit allows tests on a wastewater sanitation system to be carried out and the flow in a sewage system to be observed.

All Scientific & Laboratory Equipment categories