Optical Tables & Isolation in Bangladesh

Optical tables, breadboards and vibration isolation for stable laboratory setups. Compare working area, load, stiffness and isolation requirements.

11 products from 1 manufacturer: ThorLabs.

Products

• Nexus Optical Tables, 210 mm (8.3") Thick — ThorLabs: All steel Nexus optical tables with a 210 mm thick honeycomb core, supplied in sizes from 1 m x 2 m up to 1.5 m x 2.5 m. The machined stainless steel top skin is tapped on a 25 mm grid and every table is individually tested for damping performance.
• Nexus Optical Tables, 310 mm (12.2") Thick — ThorLabs: A thicker Nexus optical table for demanding beam stability, offered from 1 m x 2 m up to 1.5 m x 4 m. The 310 mm core raises stiffness so that deflection under a 150 kg central load stays below 1.2 micrometres, suiting interferometry and long beam paths.
• Nexus Optical Tables, 460 mm (18.1") Thick — ThorLabs: The heaviest Nexus table, 460 mm thick, available from 1.2 m x 2 m up to 1.5 m x 4 m. The extra depth gives the highest stiffness in the range and is intended for large multi-instrument setups where relative tabletop motion must stay at the sub-nanometre level.
• Nexus Optical Breadboards, Optimized Damping, 60 mm (2.4") Thick — ThorLabs: Steel honeycomb breadboards 60 mm thick, from 300 mm x 300 mm up to 900 mm x 1200 mm. Each board is individually tested and damping is optimised per size, making them a practical mounting surface for benchtop optics and small laser setups.
• Nexus Optical Breadboards, Optimized Damping, 110 mm (4.3") Thick — ThorLabs: A 110 mm thick Nexus breadboard range covering 600 mm x 900 mm up to 1200 mm x 1800 mm. The deeper honeycomb core raises stiffness for larger optical layouts that still need to sit on a frame rather than a full optical table.
• Aluminum Breadboards: High Stiffness, 25 mm (0.98") Thick — ThorLabs: Lightweight non-magnetic breadboards built from aluminium plates over an aluminium honeycomb core. Matching the coefficient of thermal expansion throughout reduces thermal drift, and a T-slot in each side accepts 25 mm construction rails.
• Upgradeable Optical Table Supports: Rigid, Non-Isolating — ThorLabs: Free-standing rigid legs for Thorlabs optical tables, supplied in three heights with a levelling pad. They suit vibration-insensitive work such as general spectroscopy, and each leg can later be converted to passive pneumatic isolation with an upgrade kit.
• Passive Isolation Optical Table Supports — ThorLabs: Pneumatic table legs that isolate an optical table from floor vibration across the 10 to 50 Hz range where most laboratory disturbance sits. The closed oil-free system is inflated with a foot pump and needs no permanent compressed air supply.
• Optical Table Supports: Active Vibration Isolation — ThorLabs: Self-levelling pneumatic supports that isolate an optical table in both the vertical and horizontal axes from about 3 Hz upwards. The very low resonant frequency suits interferometry, nanopositioning and high resolution microscopy.
• Passive Benchtop Isolation Systems — ThorLabs: Benchtop isolation for breadboards and instruments, covering pneumatic IsoPlate platforms, bolt-on pneumatic isolator feet and sorbothane feet. They are intended for temporary setups and moderately vibration-sensitive microscopy and photonics work.
• Active Isolation Breadboard Support Frames — ThorLabs: All steel support frames carrying four air-mounted active isolators, sized for breadboards up to 1200 mm x 1800 mm. They self-level to a repeatability of 0.25 mm and suit interferometry, cell injection and non-contact surface measurement.

All Scientific & Laboratory Equipment categories